113567 | single color led controller sys-pro funk mesh pwm … · 2021. 3. 17. ·...
Post on 02-Sep-2021
0 Views
Preview:
TRANSCRIPT
113567 | Sys-Pro Funk Mesh PWM-Controller, 1-4 Kanal, 12-24V DC 4x3A
User Manual Ver 1.0.6
Betriebstemperatur
Gehäusetemperatur (max.)
Umgebung
IP20 Schutzart
Technische Details
Ausgangsleistung
Ausgangs-Strom
144-288W
4CH, 3A/CH
Ein- und Ausgang
Eingangs-Spannung 12-24VDC
Sicherheit und EMV
EMV Standard EN301 489,EN 62479
Funkanlagenrichtlinie (RED) EN300 328
Zertifikate CE, EMV, LVD, RED
EN60950Sicherheits Standard (LVD)
Ta: -30 OC ~ +55 OC
T c: +85OC
LVD
Model No.: V1-L/P
Single Color LED Controller
Eigenschaften● Hochwertiger 4 Kanal-Konstantspannungs-Controller● Ermöglicht bunte, statische oder dynamische Lichteffekte.● 2,4 GHz Funk Technologie. Bis zu 30 Meter Reichweite.● Ein Dimmer kann bis zu 10 Fernbedienungen einlernen.● Kann während des Betriebes WIFI-gesteuert werden.● RGB Änderungsmodulliste über App steuerbar.
V1-L/P Single Color LED Controller
Page 1
Mechanical Structures and Installations
● Connect with push switch
● Match with dimming remote
AC100-240VPower Supply12-24VDCConstant Voltage
27mm
175mm
160mm
45mm
Match key
Push switch common
Power input -
Power input +
LED output + Push switch
Dip switch setting
LED indicator
12
3
LED output -
12
3
Single color LED strip +
AC100-240VPower Supply12-24VDCConstant Voltage
12
3
Single color LED strip +
Push Switch
RED
Installation rack
RF remote
Wiring Diagram
V1-L/PLED Dimmer
Uin=12-24VDCIin=15.5A
Uout=12-24VDCIout=15APout=180-360W
Temp Range: -30℃-+55℃
MA
TC
H
I
N P
UT
12
-24
VD
C +
-
+
-+
-
0.5-2.0mm
2.4G
12
3
12
12
12
3
logarithmlinear
250Hz
500Hz
2KHz
8KHz
PW
M F
requency
Dim
min
g C
urve
10
A1
2A
15
A1
5A
V1-L/PLED Dimmer
Uin=12-24VDCIin=15.5A
Uout=12-24VDCIout=15APout=180-360W
Temp Range: -30 ℃-+55℃
MA
TC
H
I
N P
UT
12
-24
VD
C +
-
+
-+
-
0.5-2.0mm
2.4G
12
3
12
12
12
3
logarithmlinear
250Hz
500Hz
2KHz
8KHz
PW
M F
requency
Dim
min
g C
urve
10A
12A
15A
15A
V1-L/PLED Dimmer
Uin=12-24VDCIin=15.5A
Uout=12-24VDCIout=15APout=180-360W
Temp Range: -30 ℃-+55℃
MA
TC
H
I
N P
UT
12
-24
VD
C +
-
+
-+
-
0.5-2.0mm
2.4G
12
3
12
12
12
3
logarithmlinear
250Hz
500Hz
2KHz
8KHz
PW
M F
requency
Dim
min
g C
urve
10A
12A
15A
15A
Dimensionen
User Manual Ver 1.0.6
Operation temperature
Case temperature (Max.)
Environment
IP20IP ratingDimming data
Dimming range
RF 2.4GHz + Push Dim
30m(Barrier-free space)
4096 (2^12) levels
0 -100%
Technical Parameters
Output power 180W/360W (12V/24V)
Output voltage 12-24VDC
Output current 1CH,15A
Input and Output
Input voltage 12-24VDC
Input current 15.5A
Safety and EMC
EMC standard (EMC) EN301 489,EN 62479
Radio Equipment(RED) EN300 328
Certification CE,EMC,LVD,RED
EN60950Safety standard(LVD)
Output type Constant voltage
Input signal
Control distance
Dimming gray scale
Ta: -30 OC ~ +55 OC
Tc:+85OC
LVD
Model No.: V1-L/P
Single Color LED Controller
1 Channel/Step-less dimming/Wireless remote control/Push Dim/Four PWM frequency/Linear or logarithmic dimming
Features● 4096 levels 0-100% dimming smoothly without any flash.
● Match with Skydance’s 2.4G single zone or multiple zone dimming remote control.
● One RF controller accept up to 10 remote control.
● Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
● Synchronize on multiple number of controllers.
● Connect with external push switch to achieve on/off and 0-100% dimming function.
● Logarithmic or linear dimming curve selectable.
● PWM frequency 250Hz, 500Hz, 2kHz or 8kHz selectable.
● Over-heat / Over-load / Short circuit protection, recover automatically.
Page 1
113567 | Sys-Pro Funk Mesh PWM-Controller, 1-4 Kanal, 12-24V DC 4x3A
Dimming curve Logarithmic or linear
250Hz, 500Hz, 2kHz, 8kHzPWM Frequency
RED
Warranty and Protection
5 years
Protection
Reverse polarityOver-heat Over-load Short circuit
Warranty
Schaltplan RGBW:
Schaltplan Zweifarbig:
Schaltplan 4x Einfarbig:
User Manual Ver 1.0.6
V1-L/P Single Color LED Controller
Page 2
113567 | Sys-Pro Funk Mesh PWM-Controller, 1-4 Kanal, 12-24V DC 4x3A
Dimming curve setting
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM
dut
y(%
)100
90
80
70
60
50
40
30
20
10
PWM
dut
y(%
)
50 60 70 80 90 100
Brightness(%)10 20 30 40
Gamma=1.6
50 60 70 80 90 100
Brightness(%)10 20 30 40
Gamma=1.0
3 3
100
90
80
70
60
50
40
30
20
10
PWM
dut
y(%
)
PWM frequency setting
We can select four PWM frequency: 250Hz, 500Hz, 2kHz or 8kHz.Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video). 1 2 1 2 1 2 1 2
250Hz500Hz2KHz8KHz
Push Dim Function
● Short press: Turn on or off light.
● Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction.
● Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure.
● Synchronization:
If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%. This means there is no need for any additional synchrony wire in larger installations. We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters.
The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching(momentary) wall switchs.
10A 12A 15A 15A
Verbindung zu anderen Sys-Eco Komponenten:
1. Einlernen:Kurze Betätigung des Knopfes „Match“ am Dimmer. Dann innerhalb von 5 Sekunden Betätigung des Knopfes „on/off“ oder„Zone“ auf der Fernbedienung. Das Leuchtmittel blinkt als Bestätigung 1x auf.
2. Löschen:Lange Betätigung des Knopfes „Match“ (länger als 5 Sekunden) löscht alle eingelernten Verbindungen. Das Leuchtmittelblinkt als Bestätigung 2x auf.
3. Bei mehreren Zonen:Nach Betätigung der Taste „Match“ am Dimmer innerhalb von 5 Sekunden die gewünschte Zone auf der Fernbedienungwählen und diese kurz betätigen. Das Leuchtmittel blinkt als Bestätigung 1x auf.
Fehleranalyse & Behebung
Fehlerbild Mögliche Fehlerursache Behebung Kein Licht 1. Kein Strom.
2. Falsch Angeschlossen – siehe Schaltplan.1. Kontrolle Stromquelle.2. Kontrolle Anschlussplan.
Nicht homogenes Lichtbild. Spannungsabfall.
1. Anschlusskabel ist zu lang.2. Kabeldurchmesser ist zu klein.3. Überlastung der Stromversorgung.4. Zu hohe Last für den Controller.
1. Reduzierung der Kabellänge.2. Verwendung eines breiteren Anschlusskabels.3. Höhere Stromversorgung.4. Verwendung eines Verstärkers.
Fernbedienung funktioniert nicht.
1. Batterie leer.2. Entfernung zwischen Fernbedienung undDimmer ist zu weit.3. Die Geräte wurden nicht richtig aufeinander eingelernt.
1. Ersetzen der Batterie.2. Reduzierung der Entfernung.3. Erneutes Einlernen der Komponenten –siehe auch „Verbindung zu anderen Sys-Eco Komponenten“.
Sicherheitsinformation
1. Das Produkt darf ausschließlich von qualifizierten Fachpersonal in Betrieb genommen werden.2. Das Produkt muss vor direkter Sonneneinstrahlung und Feuchtigkeit geschützt werden. Das Produkt ist nicht für den
Außenbereich geeignet.3. Eine gute Wärmeableitung sowie ausreichende Lüftung verlängern die Lebensdauer des Produktes.4. Bitte überprüfen Sie, dass die Ausgangsspannung des verwendeten Netzteiles mit der Arbeitsspannung des Gerätes
kompatibel ist.5. Stellen Sie sicher, dass alle Kabelverbindungen und Polaritäten korrekt verbunden sind.6. Wenn das Produkt nicht einwandfrei funktioniert wenden Sie sich bitte an ISOLED®. Versuchen Sie nicht, das
Produkt selber zu reparieren und öffnen Sie das Produkt unter keinen Umständen.
top related