montageanleitung/ fitting manual bplse..(-fe, -oe)
Post on 12-May-2022
4 Views
Preview:
TRANSCRIPT
SeiteLieferausführung kontrollieren ................................. 2
Einbau von BPLSE..(-FE, -OE) .................................... 6
Führungswagen demontieren ................................... 7
Vorbereitungen für den BPLSE..(-FE, -OE)-Einbau...... 8
BPLSE..(-FE, -OE) einbauen....................................... 9
Führungswagen aufschieben,BPLSE..(-FE, -OE) fertig montieren............................. 11
PageChecking the delivered condition ............................. 2
Fitting of the BPLSE..(-FE, -OE) .................................. 6
Removing the carriage.............................................. 7
Preparations for fitting of the BPLSE..(-FE, -OE) ......... 8
Fitting of the BPLSE..(-FE, -OE) .................................. 9
Slide the carriage on the guideway,final fitting of the BPLSE..(-FE, -OE) ........................... 11
0001
4216
Montageanleitung/Fitting manualBPLSE..(-FE, -OE)für / for KUSE..(-L, -H, -HL)
2
Lieferausführung kontrollieren
Ein BPLSE..-FE besteht aus:� Schmieradapterplatte� Verschlussschraube� Spezialschraube� Dichtring� Schmiernippel
Checking the delivered condition
A BPLSE..-FE consists of:� a lubrication adapter plate� a screw plug� a special screw� a sealing ring� a lubrication nipple
21
34
5
0001
4217
3
Lieferausführung kontrollieren
Ein BPLSE..-OE besteht aus:� Schmieradapterplatte� Verschlussschraube� Spezialschraube� Dichtring� Zentralschmieranschluss� Dichtring
Checking the delivered condition
A BPLSE..-OE consists of:� a lubrication adapter plate� a screw plug� a special screw� a sealing ring� a central lubrication connector� a sealing ring
21
3 4
67
0001
4218
4
Lieferausführung kontrollieren
Ein BPLSE45-FE besteht aus:� Schmieradapterplatte� Verschlussschraube� Spezialschraube� Dichtring� Schmiernippel� Befestigungsschrauben
Checking the delivered condition
A BPLSE45-FE consists of:� a lubrication adapter plate� a screw plug� a special screw� a sealing ring� a lubrication nipple� fixing screws
2 1
34
5
8
0001
421D
5
Lieferausführung kontrollieren
Ein BPLSE45-OE besteht aus:� Schmieradapterplatte� Verschlussschraube� Spezialschraube� Dichtring� Zentralschmieranschluss� Dichtring� Befestigungsschrauben
Checking the delivered condition
A BPLSE45-OE consists of:� a lubrication adapter plate� a screw plug� a special screw� a sealing ring� a central lubrication connector� a sealing ring� fixing screws
2 1
34
6
8
7
0001
421E
6
Einbau von BPLSE..(-FE, -OE)
Achtung!Wir empfehlen, den Führungswagen während desEinbaus der BPLSE..(-FE, -OE) von der Schiene zutrennen! Die Demontage des Führungswagens istaber nicht zwingend erforderlich! Beim Einbau derBPLSE..(-FE, -OE) Wagen vor Verschmutzung schützen und auf Schutzschiene � lassen!
Fitting of the BPLSE..(-FE, -OE)
Caution!We recommend that the carriage is separate from the guideway while the BPLSE..(-FE, -OE) is being fitted. However, it is not absolutely essential to removethe carriage. While fitting the BPLSE..(-FE, -OE), protect the carriage against contamination and do not remove the dummy guideway �.
13 12
0001
421F
7
Führungswagen demontieren
❑ Schutzschiene � vor die Führungsschiene setzen und den Führungswagen � auf die Schutzschiene schieben.
Achtung!Schutzschiene im Wagen lassen!Die Schutzschiene � verhindert Schäden am Wälzkörpersatz und schützt vor Wälzkörperverlust, wenn der Wagen von der Schiene getrennt ist!
Removing the carriage
❑ Position the dummy guideway � against the guideway and slide the carriage � onto thedummy guideway.
Caution!Leave the dummy guideway in the carriage.The dummy guideway � prevents damage to the rolling element set and the loss of rolling elements while the carriage is separate from the guideway.
12
13
14
0001
4220
8
Vorbereitungen für den BPLSE..(-FE, -OE)-Einbau
❑ Führungswagen an Schienenende fahren undgegebenenfalls Schmiernippel entfernen.
BPLSE45(-FE, -OE)❑ Schrauben � und Frontblech � entfernen,
diese Bauteile werden nicht mehr benötigt.
Preparations for fitting of the BPLSE..(-FE, -OE)
❑ Slide carriage to the end of the guideway and remove the lubrication nipple if appropriate.
BPLSE45(-FE, -OE)❑ Remove screws � and end plate �.The parts removed are no longer required.
16
10
9
9
0001
4844
9
BPLSE..(-FE, -OE) einbauen
❑ Schmieradapterplatte � vor das Kopfstück setzen und mit Spezialschraube � und Dichtring �montieren, Spezialschraube leicht anziehen.
Achtung!Bei Verwendung einer ungeeigneten Schraube wird die Schmierstoffzufuhr blockiert!Ausschließlich Spezialschraube � verwenden!
Fitting of the BPLSE..(-FE, -OE)
❑ Position the lubrication adapter plate � against the end piece and mount using the special screw � and sealing ring �. Tighten the special screw slightly.
Caution!The lubricant feed system will become blocked if anunsuitable screw is used.Use the special screw � only.
1
3
4
0001
46C
6
10
BPLSE..(-FE, -OE) einbauen
❑ Schmiernippel � (bei BPLSE..-FE) oderZentralschmieranschluss � (bei BPLSE.. -OE) und Dichtring � auf der gewünschten Seite montieren.
❑ Verschlussschraube � montieren.
BPLSE45(-FE, -OE)❑ Schmieradapterplatte � mit Befestigungs-
schrauben � fixieren, Schrauben handfest anziehen.
Fitting of the BPLSE..(-FE, -OE)
❑ Mount the lubrication nipple � (for BPLSE..-FE)or central lubrication connector � (for BPLSE..-OE) and the sealing ring � on the required side.
❑ Mount the screw plug �.
BPLSE45(-FE, -OE)❑ Secure the lubrication adapter plate � using fixing
screws �, tighten screws finger-tight.
1
2
8 67
5
000
146E
1
11
Führungswagen aufschieben,BPLSE..(-FE, -OE) fertig montieren
Achtung!Die BPLSE45(-FE, -OE) wird durch Befestigungs-schrauben � zentriert, andere Baugrößen müssenvon Hand zentriert werden!
❑ Führungswagen � auf Führungsschiene schieben.❑ Schmieradapterplatte � zur Führungsschiene so
ausrichten, dass ein umlaufend gleichmäßiger Spalt entsteht.
❑ Spezialschraube � anziehen, Anziehdrehmomentbeachten, siehe Bild.
Slide the carriage on the guideway,final fitting of the BPLSE..(-FE, -OE)
Caution!BPLSE45(-FE, -OE) is centred using fixing screws �. Other sizes must be centred manually.
❑ Slide the carriage � onto the guideway .❑ Align the lubrication adapter plate � with the
guideway so that there is a uniform gap all theway round.
❑ Tighten the special screw �, observing the tightening torque, see picture.
13
14
000
146E
F
8
113
8
3 1,5 Nm
000
146E
E
MAT
NR
0075
9208
6-00
00 /
MO
N 0
3 /
D/G
B-D
/GB
/ 2
0080
85 /
Pri
nted
in G
erm
any
by
Man
delk
ow
Schaeffler KG
Geschäftsbereich Lineartechnik
Berliner Straße 134
66424 Homburg (Saar)
Internet www.schaeffler.de
E-Mail info.linear@schaeffler.com
In Deutschland:
Telefon 0180 5003872
Telefax 0180 5003873
Aus anderen Ländern:
Telefon +49 6841 701-0
Telefax +49 6841 701-2625
Schaeffler (UK) Ltd
Forge Lane, Minworth
Sutton Coldfield
West Midlands · B76 1AP
Telephone 0121 351 3833
Fax 0121 351 7686
E-Mail info.uk@schaeffler.com
Website www.schaeffler.co.uk
Nachdruck, auch auszugsweise, nur mit
unserer Genehmigung.
This publication or parts thereof may not
be reproduced without our permission.
© Schaeffler KG · 2008, August
MON 03 D/GB-D/GB
top related