s7 edutrainer it bedienungsanleitung s7 edutrainer it ... · lehrbuch tp 301 de best.-nr. 093 310...
Post on 25-Mar-2020
6 Views
Preview:
TRANSCRIPT
662569 DE/GB
07/02
S7 EduTrainer IT
Bedienungsanleitung
S7 EduTrainer IT
Operating instructions
Bestell-Nr.: 662569
Benennung: BED.ANL.EDUT.IT
Bezeichnung: D:LP-S7ET-IT-DE/GB
Stand: 07/2002
Autoren: Roland Ackermann
Grafik: Doris Schwarzenberger
Layout: 10.07.2002 Beatrice Huber
© Festo Didactic GmbH & Co., D-73770 Denkendorf, 2002
Internet: www.festo.com/didactic
e-mail: did@festo.com
Weitergabe sowie Vervielfältigung dieses Dokuments, Verwertung und
Mitteilung seines Inhalts verboten, soweit nicht ausdrücklich gestattet.
Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte
vorbehalten, insbesondere das Recht, Patent-, Gebrauchsmuster- oder
Geschmacksmusteranmeldungen durchzuführen.
The copying, distribution and utilisation of this document as well as the
communication of its contents to others without expressed
authorisation is prohibited. Offenders will be held liable for the payment
of damages. All rights reserved, in particular the right to carry out
patent, utility model or ornamental design registration.
Inhalt
Contents
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 3
1. Einleitung __________________________________________4
2. Aufbau und Funktion _________________________________5
3. Funktionsbeschreibung des Kommunikationsprozessors
CP 343-1 IT _________________________________________6
4. Technische Daten ____________________________________8
5. Programmiersoftware, Dokumentation, Teachware ________11
6. Programmiersoftware für die SPS-Funktionalität
(Sonderpakete für Bildungseinrichtungen) _______________12
7. Aufbau ____________________________________________15
8. Beispiel zum Anschluss von Festo Didactic-Komponenten
an den S7 EduTrainer IT _____________________________16
9. Sicherheitshinweise _________________________________17
1. Introduction________________________________________19
2. Design and function _________________________________20
3. Functional description of communication processor
CP 343-1 IT ________________________________________21
4. Technical data ______________________________________23
5. Programming software, documentation, Teachware _______26
6. Programming software for the PLC functionality
(special packages for training facilities) _________________27
7. Design ____________________________________________30
8. Example for the connection of Festo Didactic components
to the S7 EduTrainer IT ______________________________31
9. Notes on safety _____________________________________32
Deutsch
English
1. Einleitung
4 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
Teleteaching, Teletraining und Tele-Engineering sind neue
Anwendungen der Informationstechnologien (IT). Mittels Internet
können alle Geschäftsprozesse eines Unternehmen miteinander
verbunden und Informationen von außen abgerufen bzw. verändert
werden. Dadurch wird das Anpassen von SPS-Programmen,
Inbetriebnahme von Anlagen, Teleservice und die Übertragung von
komplexen Produktionsdaten möglich.
Mit dem S7 EduTrainer IT Best.-Nr. 527423 erhalten Sie eine kompakte
Einheit, die sowohl als Master für die verteilte Intelligenz von
Steuerungsprojekten genutzt (Profibus-DP) als auch für das Erlernen
der Elemente des Teleteaching und Tele-Engineering (Ethernet)
eingesetzt werden kann.
Der im Kommunikationsprozessor integrierte Web-Server gestattet den
Zugriff auf System- und Prozessdaten über den Web-Browser. Die
E-Mail-Funktion des CP ermöglicht der S7-300 elektronische
Nachrichten an übergeordnete Systeme zu senden.
2. Aufbau und Funktion
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 5
Die Einheit im ER-Format ist für den Einsatz in den Aufnahmerahmen
des Festo Didactic Labormöbelsystems, auf der blauen Stecktafel oder
Profilplatte bzw. als Tischgerät geeignet und besteht aus folgenden
Komponenten:
• Simatic S7 315-2DP
• Kommunikationsprozessor Simatic CP 343-1 IT (Ethernet-Modul mit
integriertem Web-Server)
Die Spannungsversorgung muß über eine externe 24 V DC-Quelle
erfolgen. Dafür bieten sich die Netzgeräte von Festo Didactic an, die als
Einschubvariante für den ER-Aufnahmerahmen oder als Tischvariante
verfügbar sind. Für den Einsatz des S7 EduTrainer IT auf der
Profilplatte sind 4 Adapter Best.-Nr. 323571 notwendig.
Im Lieferumfang sind weiterhin enthalten:
• S7/Step7-Dokumentation auf CD-ROM
• CD-ROM “Simatic IT-Lösungen für die Ausbildung”
• CD-ROM „Beispiele für die Ausbildung mit Step 7, AS-Interface und
Profibus-DP sowie PPT-Shows über AS-Interface, Verteilte
Automation mit Profibus-DP und Ventilinseln“
Das Kernstück ist die CD-ROM “Simatic IT-Lösungen für die Ausbildung”
mit ausführlichen Informationen zu Teleteaching und Tele-Engineering,
zu Einsatzbeispielen und -szenarien aus der Schulpraxis für die
Schulpraxis bis zur kompletten Anleitung für den Aufbau eines
Teleteaching-Arbeitsplatzes mit Simatic.
Die weitere CD-ROM enthält Beispiele für die Ausbildung mit Step 7,
AS-Interface und Profibus-DP sowie PPT-Shows über AS-Interface,
Verteilte Automation mit Profibus-DP und Ventilinseln.
3. Funktionsbeschreibung des Kommunikations-
prozessors CP 343-1 IT
6 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
Der CP 343-1 IT ist die Kommunikationsbaugruppe der
SIMATIC S7-300 für Industrial Ethernet.
Mit einem eigenen Prozessor entlastet er die CPU von
Kommunikationsaufgaben und ermöglicht weitere zusätzliche
Verbindungen.
Kommunikationsmöglichkeiten der S7-300 über CP 343-1 IT mit:
• Programmiergeräten, Rechnern, Bedien- und Beobachtungsgeräten
• anderen SIMATIC S7-Systemen
• SIMATIC S5-Automatisierungsgeräten
• Einbindung in die Informationstechnik (IT) über E-Mail und Web-
Browser
Der CP 343-1 IT kann in sein Filesystem neben HTML-Seiten auch z. B.
Maschinendokumentation oder Anwenderhilfen aufnehmen.
Der CP 343-1 IT wickelt den Datenverkehr über Industrial Ethernet
selbständig ab. Die Baugruppe besitzt einen eigenen Prozessor. Die
Schichten 1 bis 4 entsprechen den internationalen Standards.
Der Multiprotokollbetrieb der Transportprotokolle ISO und TCP/IP ist
möglich.
Der CP 343-1 IT arbeitet im Multiprotokollbetrieb für folgende
Kommunikationsdienste:
Mit Hilfe der PG/OP-Kommunikation können alle am Netz
angeschlossenen S7-Stationen fernprogrammiert werden.
Mit Hilfe von S7-Routing ist es möglich, die PG/OP-Kommunikation
netzwerkübergreifend zu nutzen.
Zur Anbindung der S7-300 (nur Server) an S7-400 (Server und Client),
Bedien- und Beobachtungsgeräten und PCs (CP 1613 mit S7-1613 oder
SOFTNET-S7).
Die Kommunikation erfolgt ohne weitere Projektierung auf dem
CP 343-1 IT.
PG/OP-Kommunikation
S7-Routing
S7-Kommunikation
3. Funktionsbeschreibung des Kommunikationsprozessors CP 343-1 IT
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 7
Auf der Basis der Schicht 4 eine einfache und optimierte Schnittstelle
für die Datenkommunikation.
Es können bis zu 8 Kbyte in einem Aufruf übertragen werden.
Mit dieser Schnittstelle können
• ISO-Transport
• TCP-Transport mit RFC 1006 (z. B. CP 1430 TCP) oder ohne RFC1006
und
• UDP als Übertragungsprotokoll des CP 343-1 IT genutzt werden.
S5-kompatible Kommunikation wird für die Kommunikation zu SIMATIC
S5, SIMATIC S7-400/-300 und Rechnern/PC eingesetzt. Die
erforderlichen Funktionsaufrufe sind Bestandteil von NCM S7 für
Industrial Ethernet und in das S7-Anwenderprogramm einzubinden.
Über S5-kompatible Kommunikation mit FETCH/WRITE ist ein direkter
Zugriff auf die CPU-Daten wie bei dem CP1430 möglich. Vorhandene
HMI-Systeme können so weiter verwendet werden.
• Web-Server; HTML-Seiten können über Standard-Browser abgerufen
werden
• Standard-Webseiten; zur Beobachtung der S7-300-Steuerung. Die
Seiten können mit beliebigen HTML-Tools erstellt werden
• E-Mails; Versendung von E-Mails aus dem Anwenderprogramm
heraus über FC-Aufrufe
S5-kompatible
Kommunikation
IT-Funktionen
4. Technische Daten
8 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
Allgemein
Betriebsspannung S7 24 V DC
(wird von externem Netzgerät geliefert)
Datensicherung Batterie
Abmessungen 145 x 170 x 240 mm (H x B x T)
Gewicht Ca. 2 kg
Schutzart IP 20
4. Technische Daten
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 9
CP 343-1 IT
Übertragungsrate 10 Mbit/s und 100 Mbit/s
Schnittstellen Anschluss an Industrial Ethernet (10/100 Mbit/s)
15-polige Sub-D-Buchse (automatische Umschaltung
zwischen AUI und Industrial Twisted Pair)
10BaseT, 100BaseTX RJ45
Versorgungsspannung 4-polige Klemmleiste
Versorgungsspannung DC +5 V (±5%) und DC +24 V (±5%)
Stromaufnahme aus Rückwandbus 70 mA
aus DC 24 V extern ca. 0,58 A
Projektiersoftware NCM S7 für Industrial Ethernet (wird mit STEP/V5.x ausgeliefert)
Leistungsdaten
S5-kompatible Kommunikation
(SEND/RECEIVE)
Anzahl TCP/IP-Verbindungen max. 16
Anzahl ISO-Verbindungen max. 16
Anzahl Nutzdaten max. 8 Kbyte
Anzahl gleichzeitiger UDP-Aufträge max. 16
Anzahl Nutzdaten bei UDP max. 2048 Kbyte
Anzahl der ISO/TCP-Transportverbindungen max. 16
S7- und PG/OP-Kommunikation Anzahl Verbindungen1 max. 16
IT-Kommunikation Anzahl Verbindungen zu einem E-Mail-Server max. 1
Speicherkapazität des Filesystems 10 Mbyte
Multiprotokollbetrieb Summe aller gleichzeitig betreibbaren Verbindungen
max. 32
1 Nutzung abhängig von der Leistung der verwendeten S7-CPU/FM
4. Technische Daten
10 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
CPU 315-2DP
Arbeitsspeicher 64 KByte/21K Anweisungen RAM (integriert)
(1 Anweisung entspricht durchschnittlich 3 Byte)
Ladespeicher integriert 96 KByte RAM
steckbar als MC, max. 4 MByte Flash-EPROM
Pufferung ohne Batterie 4 KByte; Merker, Zähler, Zeiten und Daten
mit Batterie alle Bausteine
Echtzeituhr ja
Merker 2048
Zähler 64
Zeiten 128
MPI-Schnittstelle Teilnehmerzahl, max.
32 Teilnehmer am MPI-Bus; PG/PC, OP, weitere
S7-300®/400®, C7; je CPU max. 4 statische und
8 dynamische Verbindungen
Übertragungsgeschwindigkeit 187,5 kbit/s
PG/PCs mit STEP® 7 über MPI Schnittstelle anschließbar
Anzahl DP-Stränge je CPU (integrierte Schnittst./CP 342-5) 1/1
DP-Master-Stationen je CPU (integrierte Schnittst./CP 342-5) 64/64
DP-Anschluss (Master/Slave) 1 (CP 342-5)
Versorgungsspannung Nennwert DC 24 V
zulässiger Bereich 20,4 – 28,8 V
Stromaufnahme, typ 1 A
Betreibbare Software S7-GRAPH KOP
S7-HiGraph AWL
S7-SCL FUP
CFC
5. Programmiersoftware, Dokumentation, Teachware
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 11
Die Programmierung der S7 315-2DP erfolgt mit der
Programmiersoftware STEP 7 nach EN 61131.
Zum Anschluss des S7 EduTrainer IT über die MPI-Schnittstelle der
CPU an die serielle Schnittstelle des PC ist ein Kabel mit Adapter
Best.-Nr. 184555 erforderlich.
Handbuch S7-300 DE Best.-Nr. 184 557
Handbuch S7-300 GB Best.-Nr. 184 558
STEP 7-Grundwissen DE Best.-Nr. 185 563
STEP 7-Grundwissen GB Best.-Nr. 185 564
STEP 7-Referenzhandb. AWL, KOP, FUP DE Best.-Nr. 184 565
STEP 7-Referenzhandb. AWL, KOP, FUP GB Best.-Nr. 184 566
(Alle Dokumente sind als PDF-Files auf der im Lieferumfang des S7
EduTrainer IT enthaltenen CD-ROM „S7/Step7-Dokumentation“
verfügbar.)
Arbeitsbuch TP 301 DE Best.-Nr. 093 313
Arbeitsbuch TP 301 GB Best.-Nr. 093 314
Lehrbuch TP 301 DE Best.-Nr. 093 310
Lehrbuch TP 301 GB Best.-Nr. 093 311
Lösungsteil TP 301 mit STEP 7 DE Best.-Nr. 094 524
Lösungsteil TP 301 mit STEP 7 GB Best.-Nr. 094 537
Weitere Informationen dazu finden Sie auf der CD-ROM „Beispiele für
die Ausbildung mit Step 7, AS-Interface und Profibus-DP sowie PPT-
Shows über AS-Interface, Verteilte Automation mit Profibus-DP und
Ventilinseln“.
Alle Informationen zur Anwendung der IT-Funktionalität sind auf der
mitgelieferten CD-ROM “Simatic IT-Lösungen für die Ausbildung”
enthalten.
Empfohlene Siemens-
Dokumentation
Empfohlene Teachware
6. Programmiersoftware für die SPS-Funktionalität
12 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
1. Software für den nicht-gewerblichen Bereich (öffentliche
Bildungseinrichtungen)
Darunter fallen Schulen, Fachhochschulen, Universitäten,
überbetriebliche Ausbildungsstätten von öffentlichen Auftraggebern
(IHK, HWK).
• mit 12 Lizenzen von STEP 7 Professional und S7-HiGraph als
Ausstattung für die Rechner in einer Ausbildungsstätte
• mit 48 Stück Hausaufgaben-Software (Software for Students)
Eine Lieferung besteht aus folgenden Teilen:
• 12 x Multiautorisierungsdiskette, die die Autorisierungen und Not-
Autorisierungen von Step 7 Professional (siehe nächster Absatz) und
S7-HiGraph beinhaltet
• 1 x CD Step 7 Professional
– Step 7 Basis (AWL, KOP, FUP)
– S7-SCL
– S7-GRAPH
– S7-PLCSIM
• 1 x CD S7-HiGraph
• 1 x Allgemeine Bedingungen zur Überlassung von Software für
Automatisierungs- und Antriebstechnik
• 1 x Software-Produktschein
• 48 x Software for Students (als Hausaufgaben-Software); 120 Tage-
Lizenz bestehend aus
– Step 7 Basis (AWL, KOP, FUP)
– PLCSIM
Best.-Nr. 531141
• Kein Verkauf an Bildungseinrichtungen aus dem gewerblichen
Bereich!
Step 7 Trainer Package
Bestellinformation
6. Programmiersoftware für die SPS-Funktionalität
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 13
Inhalt wie Step 7 Trainer Package
Best.-Nr. 531142
• Kein Verkauf an Bildungseinrichtungen aus dem gewerblichen
Bereich!
1 x Hausaufgaben-Software
• Step 7 Basis (AWL, KOP, FUP)
• S7-PLCSIM
Eine Lieferung besteht aus folgenden Teilen:
• 1 x CD Step 7 Basis
• 1 x CD S7-PLCSIM
• 1 x Multiautorisierungsdiskette; Lizenzierung begrenzt auf 120 Tage
• 1 x Allgemeine Bedingungen zur Überlassung von Software für
Automatisierungs- und Antriebstechnik
• 1 x Software-Produktschein
Best.-Nr. 531143
• Voraussetzung für den Bezug:
Ein Step 7 Trainer Package Best.-Nr. 531141 muss an der Schule
vorhanden sein!!
• Kein Verkauf an Bildungseinrichtungen aus dem gewerblichen
Bereich!!
Step 7 Trainer Package
Upgrade auf neueste
Version
Bestellinformation
Software for Students
Bestellinformation
6. Programmiersoftware für die SPS-Funktionalität
14 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
2. Software für den gewerblichen Bereich (betriebliche
Bildungseinrichtungen)
• mit einer Lizenz Step 7 Professional
Eine Lieferung besteht aus folgenden Teilen:
• 1 x Multiautorisierungsdiskette, die die Autorisierungen und Not-
Autorisierungen von Step 7 Professional (siehe nächster Absatz)
beinhaltet
• 1 x CD Step 7 Professional
– Step 7 Basis (AWL, KOP, FUP)
– S7-SCL
– S7-GRAPH
– S7-PLCSIM
• 1 x Allgemeine Bedingungen zur Überlassung von Software für
Automatisierungs- und Antriebstechnik
• 1 x Software-Produktschein
Best.-Nr. 531144
• Dieses Paket kann auch an Bildungseinrichtungen aus dem nicht-
gewerblichen Bereich zusätzlich zu einem Trainer Package
(Best.-Nr. 531141) abgegeben werden, wenn ein weiteres Trainer
Package zu umfangreich wäre.
Simatic S7 Software for
Training
Bestellinformation
7. Aufbau
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 15
1 CPU 315-2DP
2 Kommunikationsprozessor CP 343-1IT
3 24 V-Sicherheitssteckbuchse
4 0 V-Sicherheitssteckbuchse
8. Beispiel zum Anschluss von Festo Didactic-
Komponenten an den S7 EduTrainer IT
16 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
Profibus-DP Komponenten
S7 EduTrainer IT
TCP/IP (Ethernet)
� @
Profibus-Kabel
50 cm Best.-Nr. 533035
200 cm Best.-Nr. 533036
Profibus-DP-Ventilinsel
Best.-Nr. 527432
Ethernet-Kabel
Normal Best.-Nr. 533037
gekreuzt Best.-Nr. 533038
S7 ET200S EduTrainer
Best.-Nr. 527425
E/A-Kabel Best.-Nr. 167106 �
�
EasyPort Best.-Nr. 167121
�
� SysLink-Kabel Best.-Nr. 34031
�
Universal-AE Best.-Nr. 162231
�
RS232-Kabel Best.-Nr. 162305
�
COSIVIS Software
(Prozesssimulation)
Touchpanel 170A (auf Anfrage)
Kabelsatz Best.-Nr. 167091
�
Gerätesatz TP 201 Best.-Nr. 184460
Gerätesatz TP 301 Best.-Nr. 167101
9. Sicherheitshinweise
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 17
Der S7 EduTrainer IT ist nach dem heutigen Stand der Technik und den
anerkannten sicherheitstechnischen Regeln gebaut. Dennoch können
bei dessen unsachgemäßer Verwendung Gefahren für Leib und Leben
des Benutzers oder Dritter und Beeinträchtigungen des EduTrainers
entstehen. Der S7 EduTrainer IT sind daher nur zu benutzen
• für die bestimmungsgemäße Verwendung im Lehr- und
Ausbildungsbetrieb
• in sicherheitstechnisch einwandfreiem Zustand
Störungen, die die Sicherheit beeinträchtigen können, sollten beim
Schulungsbetrieb nicht erzeugt werden und sind umgehend zu
beseitigen.
18 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
1. Introduction
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 19
Teleteaching, teletraining and tele-engineering are new applications in
information technology (IT). With the help of the Internet, it is possible
to join together all the business procedures of a company and call up or
change information externally. This facilitates the adaptation of PLC
programmes, the commissioning of systems, teleservice and the
transmission of complex production data.
With the S7 EduTrainer IT Order No. 527423, you have a compact unit,
which can be used as a master for the decentralised intelligence of
control projects (Profibus-DP) and for learning the element of
teleteaching and tele-engineering (Ethernet).
The web server integrated into the communication processor permits
access to system and process data via the web browser and the CP
e-mail function enables the S7-300 to transmit electronic messages.
2. Design and function
20 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
The unit in ER format is suitable for use on the cabinet frames of the
Festo Didactic Learnline system, on the blue plug-in boards or slotted
assembly boards or as a table unit and consists of the following
components:
• Simatic S7 315-2DP
• Communication processor Simatic CP 343-1 IT (Ethernet module
with integrated web server)
The voltage supply must be effected via an external 24 V DC source. The
power supply units from Festo Didactic are suitable for this and are
available in the form of a function card variant for ER cabinet frames or
as a table variant. 4 adapters Order No. 323571 are required if the S7
EduTrainer IT is to be used on a slotted assembly board.
The following are also included in the scope of delivery:
• S7/Step7 documentation on CD-ROM
• CD-ROM “Simatic IT solutions for training”
• CD-ROM „Examples for training with Step 7, AS-interface and
Profibus-DP as well as PPT presentations via AS-interface,
decentralised automation using Profibus-DP and valve terminals“
The core item is the CD-ROM “Simatic IT solutions for training” with
detailed information regarding teleteaching and tele-engineering,
application examples and practical classroom situations for practice in
the classroom, plus complete instructions for the design of a
teleteaching workstation with Simatic.
The additional CD-ROM contains examples for training with Step 7,
AS-interface and Profibus-DP as well as PPT presentations via
AS-interface, decentralised automation using Profibus-DP and valve
terminals.
3. Functional description of the communication
processor CP 343-1 IT
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 21
The CP 343-1 IT is the communication module of the
SIMATIC S7-300 for Industrial Ethernet.
With its own processor, it frees the CCU of communication functions and
facilitates additional connections.
Communication options of the S7-300 via CP 343-1 IT with:
• Programming devices, computers, control and monitoring devices
• Other SIMATIC S7 systems
• SIMATIC S5 automation equipment
• Integration into information technology (IT) via e-mail and web
browser
Apart from HTML pages, the CP 343-1 IT file system can for example also
incorporate machine documentation or user help.
The CP 343-1 IT processes the data exchange independently via
Industrial Ethernet. The module has it own processor. Levels 1 to 4
correspond to international standards.
Multiprotocol mode of the transport protocols ISO and TCP/IP is
possible.
The CP 343-1 IT operates the following communication services in
multiprotocol mode:
With the help of PG/OP communication, all S7 stations connected to the
network can be programmed remotely.
With the help of S7 routing, it is possible to make use of PG/OP
communication throughout the network.
For the connection of the S7-300 (server only) to the S7-400 (server and
client), control and monitoring devices and PCs (CP 1613 with S7-1613
or SOFTNET-S7).
Communication is effected on the CP 343-1 IT without any further
configuration.
PG/OP communication
S7 routing
S7 communication
3. Functional description of the communication processor CP 343-1 IT
22 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
A simple and optimised interface for data communication based on
level 4.
Up to 8 kByte can be transmitted in one call.
The following can be made use of with this interface
• ISO transport
• TCP transport with RFC 1006 (e.g. CP 1430 TCP),or without RFC1006
and
• UDP as transmission protocol of the CP 343-1 IT.
S5 compatible communication is used for communication with SIMATIC
S5, SIMATIC S7-400/-300 and computers/PCs. The required function
calls are a component part of NCM S7 for Industrial Ethernet and need
to be incorporated into the S7 user program.
As in the case of the CP1430, direct access is possible to CCU data via
S5-compatible communication using FETCH/WRIT. Existing HMI systems
can therefore continued to be used.
• Web server; HTML pages can be called up via the standard browser
• Standard web pages; for the monitoring of the S7-300 controller.
The pages can be set up with any HTML tools
• E-mails; despatch of e-mails from the user program via FC calls
S5 compatible
communication
IT functions
4. Technical data
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 23
General
Operating voltage S7 24 V DC
(supplied via external power supply unit)
Data backup Battery
Dimensions 145 x 170 x 240 mm (H x W x D)
Weight Approx. 2 kg
Protection classification IP 20
4. Technical data
24 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
CP 343-1 IT
Transmission rate 10 Mbit/s and 100 Mbit/s
Interfaces Connection to Industrial Ethernet (10/100 Mbit/s)
15-pin Sub-D socket (automatic changeover
between AUI and industrial twisted pair)
10BaseT, 100BaseTX RJ45
Supply 4-pin terminal strip
Supply voltage DC +5 V (±5%) and DC +24 V (±5%)
Current consumption from backwall bus 70 mA
from DC 24 V external approx. 0.58 A
Project design software NCM S7 for Industrial Ethernet (supplied with STEP/V5.x)
Performance data
S5 compatible communication
(SEND/RECEIVE)
Number of TCP/IP connections max. 16
Number of ISO connections max. 16
Number of reference data max. 8 kByte
Number of simultaneous UDP jobs max. 16
Number of reference data for UDP max. 2048 kByte
Number of ISO/TCP transport connections max. 16
S7 and PG/OP communication Number of connections1 max. 16
IT communication Number of connections to an e-mail server max. 1
Memory capacity of file system 10 Mbyte
Multiprotocol mode Total of all simultaneously operable connections
max. 32
1 Utilisation depends on the performance of the S7-CPU/FM used
4. Technical data
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 25
CPU 315-2DP
Main memory 64 KByte/21K instructions RAM (integrated)
(1 instruction corresponds to an average of 3 byte)
Load memory Integrated 96 kByte RAM
Plug-in as MC, max. 4 MByte Flash-EPROM
Buffering Without battery 4 kByte; flags, counters, timers and data
With battery All modules
Real-time clock Yes
Flags 2048
Counters 64
Timers 128
MPI interface Number of stations, max.
32 stations on MPI-Bus; PG/PC, OP, additional
S7-300®/400®, C7; max. 4 static and
8 dynamic connections per CCU
Transmission rate 187.5 kbit/s
PG/PCs with STEP® 7 Can be connected via MPI interface
Number of DP strings per CCU (Integrated interface./CP 342-5) 1/1
DP master stations per CCU (Integrated interface/CP 342-5) 64/64
DP connection (master/slave) 1 (CP 342-5)
Supply voltage Nominal value 24 V DC
Permissible range 20.4 – 28.8 V
Current consumption, typ 1 A
Software used S7-GRAPH LDR
S7-HiGraph STL
S7-SCL FCH
CFC
5. Programming software, documentation, teachware
26 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
The S7 315-2DP can be programmed using the programming software
STEP 7 to EN 61131.
A cable with adapter Order No. 184555 is required to connect the S7
EduTrainer IT to the serial interface of the PC via the MPI interface of
the CPU .
Manual S7-300 DE Order No. 184 557
Manual S7-300 GB Order No. 184 558
STEP 7 Basic knowledge DE Order No. 185 563
STEP 7 Basic knowledge GB Order No. 185 564
STEP 7 Reference manual. STL, LDR, FCH DE Order No. 184 565
STEP 7 Reference manual. STL, LDR, FCH GB Order No. 184 566
(All documents are available in the form of PDF files on a CD-ROM
„S7/Step7 documentation“, which is included in the scope of delivery of
the S7 EduTrainer IT.)
Workbook TP 301 DE Order No. 093 313
Workbook TP 301 GB Order No. 093 314
Textbook TP 301 DE Order No. 093 310
Textbook TP 301 GB Order No. 093 311
Solution part TP 301 with STEP 7 DE Order No. 094 524
Solution part TP 301 with STEP 7 GB Order No. 094 537
Further relevant information can be found on the CD-ROM „Examples for
training with Step 7, AS-interface and Profibus-DP as well as PPT
presentations via AS-interface, decentralised automation using
Profibus-DP and valve terminals“.
All information for the use of IT functionality is contained in the
supplied CD-ROM “Simatic IT solutions for training.
Recommended Siemens
documentation
Recommended teachware
6. Programming software for PLC functionality
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 27
1. Software for the non-commercial sector (state educational
establishments)
These include schools, technical colleges, universities, intercompany
training establishments of public bodies (IHK, HWK).
• With 12 licences for STEP 7 Professional and S7-HiGraph for
computer equipment in a training establishment
• With 48 copies of homework task software (software for students)
One delivery consists of the following parts:
• 12 x Multiauthorisation diskette, which contains the authorisation
for Step 7 Professional (see next paragraph) and S7-HiGraph
• 1 x CD Step 7 Professional
– Step 7 Basic (STL, LDR, FCH)
– S7-SCL
– S7-GRAPH
– S7-PLCSIM
• 1 x CD S7-HiGraph
• 1 x General conditions for permission to use the software for
automation and drive technology
• 1 x Software product certificate
• 48 x Software for Students (as homework software); 120 day license
consisting of
– Step 7 Basic (STL, LDR, FCH)
– PLCSIM
Order No. 531141
• Not for sale to educational establishments in the commercial sector!
Step 7 Trainer Package
Ordering information
6. Programming software for PLC functionality
28 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
Contents same as Step 7 Trainer package
Order No. 531142
• Not for sale to educational establishments in the commercial sector!
1 x Homework software
• Step 7 Basic (STL, LDR, FCH)
• S7-PLCSIM
One delivery consists of the following parts:
• 1 x CD Step 7 Basic
• 1 x CD S7-PLCSIM
• 1 x Multiauthorisation diskette; license is limited to 120 days
• 1 x General conditions for permission to use the software for
automation and drive technology
• 1 x Software product certificate
Order No. 531143
• Prerequisite for purchase:
One Step 7 Trainer package Order No. 531141 must be available
within the school!!
• Not for sale to educational establishments in the commercial
sector!!
Step 7 Trainer package
upgrade to latest version
Ordering information
Software for students
Order information
6. Programming software for PLC functionality
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 29
2. Software for the commercial sector (business training facilities)
• With one Step 7 Professional license
One delivery consists of the following parts:
• 1 x Multiauthorisation diskette, which contains the authorisation
and emergency authorisation of Step 7 Professional (see next
paragraph)
• 1 x CD Step 7 Professional
– Step 7 Basic (STL, LDR, FCH)
– S7-SCL
– S7-GRAPH
– S7-PLCSIM
• 1 x General conditions for permission to use the software for
automation and drive technology
• 1 x Software product certificate
Order No. 531144
• This package can also be supplied to educational establishments
from the non-commercial sector in addition to a Trainer package
(Order No. 531141), if an additional trainer package is too big.
Simatic S7 Software for
training
Ordering information
7. Design
30 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
1 CCU 315-2DP
2 Communication processor CP 343-1IT
3 24 V safety socket
4 0 V safety socket
8. Example for the connection of Festo Didactic
components to the S7 EduTrainer IT
© Festo Didactic GmbH & Co. • S7 EduTrainer IT 31
Profibus-DP components
S7 EduTrainer IT
TCP/IP (Ethernet)
� @
Profibus cable
50 cm Order No. 533035
200 cm Order No. 533036
Profibus-DP valve terminal
Order No. 527432
Ethernet-Kabel
Standard Order No. 533037
Twisted Order No. 533038
S7 ET200S EduTrainer
Order No. 527425
I/O cable Order No. 167106 �
�
EasyPort Order No. 167121
�
� SysLink cable Order No. 34031
�
Universal-IO Order No. 162231
�
RS232 cable Order No. 162305
�
COSIVIS software
(process simulation)
Touch sensitive panel 170A
(available on request)
Set of cables Order No. 167091
�
Equip. set TP 201 Order No. 184460
Equip. set TP 301 Order No. 167101
9. Notes on safety
32 © Festo Didactic GmbH & Co. • S7 EduTrainer IT
The S7 EduTrainer IT is designed to the latest state of the art
technology and is in compliance with recognised safety regulations.
However, if used incorrectly, there is a danger of injury or fatality to the
user or third parties and of damage to the EduTrainer. The
S7 EduTrainer IT should therefore only be used
• For its intended use in teaching and training establishments
• In absolutely safe condition
Malfunctions which may impair safety should not occur during training
and if so should be rectified immediately.
top related