-
1. Teileliste
10762d_1
1 Nutenstein (2x) NST-8-M6
2 Anschlussplatte MS4-6-IPM-40-80
3 Senkschraube (2x) M6x16
4 Modulverbinder MS4-/MS6-IPM
5 Hohlschraube MS4-6-IPM
6 Modulverbinder MS4-/MS6-RMV
7 Modulverbinder MS4-/MS6-MV (2x)
8 O-Ring (2x) MS4: 19x2 / MS6: 29x3
9 O-Ring 13x2
Nicht im Lieferumfang: aJ Profil
40x80/80x80 aA Bohrvorrichtung aB Flachdichtung
MS4-/MS6-NNR aC Wartungsgerät
MS4-/MS6-
Bestimmungsgemäß dient das Abzweigmodul MS4-/MS6-A-RMV-IPM-80 zur Montage eines Wartungsgeräts aC an die Längsseite eines Profils aJ.
Hinweis Der Modulverbinder MS4-/MS6-IPM 4 ist auch um 90° versetzbar für die waagrechte Montage des Wartungsgeräts aC. Beachten Sie jedoch hierbei die gerätespezifischen Vorgaben zur Einbaulage.
2. Vorbereitung zur Montage !
10762d_15
Die notwendige Bohrung muss mittig angeordnet werden.
10762d_16
Mit Hilfe der passenden Bohr-vorrichtung aA von Festo wird die genaue Position der Boh-rung gewährleistet.
10762d_17
Stellen Sie sicher, dass keine Späne im Inneren des Pro-fils aJ verbleiben.
Beim Bohren das Profilinnere gegebenenfalls unter Druck setzen.
Vorsicht Herumfliegende Späne! Augenverletzungen könnten die Folge sein. Schützen Sie Ihre Augen mit einer Schutzbrille.
3. Montage !
10762d_2
10762d_4
10762d_5
10762d_7
Bei Verwendung des Wartungs-geräts aC als Abzweigmodul.
10762d_8
Bei Verwendung des Wartungs-geräts aC als Einspeisemodul.
Hierbei wird die Flachdich-tung aB benötigt.
10762d_9
10762d_10
10762d_11
10762d_12
10762d_13
10762d_14
Für Blockmontage geeignet! Die Modulverbinder 7 sind von oben erreichbar. Sie ermögli-chen den schnellen Wechsel eines Einzelgeräts.
Montageanleitung (de) 720 543 / 2007-05a
Abzweigmodul MS4-/MS6-A-RMV-IPM-80
Festo SE & Co. KG
Postfach 73726 Esslingen ++49/(0)711/347-0 www.festo.com
2
1
8
7
7 3
6
5
4
9 @ = 11,8 _ 0,1 mm
aJ
aJ
aA
aA
3
2
1
aJ
4
2
aJ
4
2
aJ
5
aC
6
aC
6
8
8
7
6aC
7
aCMS4: 0,8 Nm _10 % MS6: 1,2 Nm _10 %
8
2
aJ
7
4
2
aJ
7
6
aC
aC
7
2
aJ
7
aC
7
2
aJ
aC
MS4: 0,8 Nm _10 % MS6: 1,2 Nm _10 %
9
4
6 Nm _ 40%
ß 14 30 Nm _ 20%
aB
p = 1 bar
@ = 11,8 _ 0,1 mm aJ
-
1. Parts list
10762d_1
1 Slot nut (2x) NST-8-M6
2 Connection plate MS4-6-IPM-40-80
3 Countersunk screw (2x) M6x16
4 Module connector MS4-/MS6-IPM
5 Hollow bolt MS4-6-IPM
6 Module connector MS4-/MS6-RMV
7 Module connector MS4-/MS6-MV (2x)
8 O-ring (2x) MS4: 19x2 / MS6: 29x3
9 O-ring 13x2
Not included in scope of delivery aJ Profile
40x80/80x80 aA Drilling machine aB Flat seal
MS4-/MS6-NNR aC Service unit
MS4-/MS6-
The branching module MS4-/MS6-A-RMV-IPM-80 is intended for the assem-bly of a service unit aC to the longitudinal side of a profile aJ.
Note The module connector MS4-/MS6-IPM 4 can also be repositioned by 90° for the horizontal assembly of a service unit aC. Please observe the device-specific specifications regarding the mounting position.
2. Preparing for assembly !
10762d_15
The required hole must be centrally located.
10762d_16
The precise position of the hole is ensured with the help of the appropriate drilling machine aA from Festo.
10762d_17
Make sure that there is no swarf inside the profile aJ.
If necessary, apply pressure to the inside of the profile during drilling.
Caution Flying swarf! Danger of eye injury. Protect your eyes with safety goggles.
4. Assembly !
10762d_2
10762d_4
10762d_5
10762d_7
If using the service unit aC as a branching module.
10762d_8
If using the service unit aC as a supply module.
The flat seal aB is required in this case.
10762d_9
10762d_10
10762d_11
10762d_12
10762d_13
10762d_14
Suitable for manifold assembly!The module connectors 7 are accessible from above. These enable the quick replacement of an individual unit.
Assembly instructions (en) 720 543 / 2007-05a
Branching module MS4-/MS6-A-RMV-IPM-80
Festo SE & Co. KG
Postfach 73726 Esslingen ++49/(0)711/347-0 www.festo.com
2
1
8
7
7 3
6
5
4
9 @ = 11,8 _ 0,1 mm
aJ
aJ
aA
aA
3
2
1
aJ
4
2
aJ
4
2
aJ
5
aC
6
aC
6
8
8
7
6aC
7
aCMS4: 0.8 Nm _10 % MS6: 1.2 Nm _10 %
8
2
aJ
7
4
2
aJ
7
6
aC
aC
7
2
aJ
7
aC
7
2
aJ
aC
MS4: 0.8 Nm _10 % MS6: 1.2 Nm _10 %
9
4
6 Nm _ 40%
ß 14 30 Nm _ 20%
aB
p = 1 bar
@ = 11.8 _ 0.1 mm aJ