-
Anchors
266
Wedge Anchor Dimensions &Performance Data
OBCI A DEVORPP W EGDE A SROHCN ,IIpuorG523-S-FF 1ssalC,4epyTLxW
tnemdebmEmuminiM)sehcni(
oTpUlairetaMsnetsaF htgneLdaerhT
seulaVraehS&elisneTetamitlUegarevA
eziSrohcnAetercnocisp0004 etercnocisp0002
elisneT raehS
4/3-1x02-4/1
1
8/3 8/7
0051 009
2x02-4/1 4/3 8/1-1
4/1-2x02-4/1 8/7 4/1-1
3x02-4/1 2/1-1 4/3
4/1-3x02-4/1 8/7-1 4/1-2
4/3-2x81-61/5
4/1-1
8/1-1 4/3-1
0091 00723x81-61/5 8/3-1 4/3-1
4x81-61/5 8/3-2 1
4/1-2x61-8/3
2/1-1
8/3 2/1-1
0063 0014
4/3-2x61-8/3 8/7 4/3-1
3x61-8/3 8/1-1 3
4/1-3x61-8/3 8/3-1 2
2/1-3x61-8/3 8/5-1 8/7-2
4/3-3x61-8/3 8/7-1 4/3-2
5x61-8/3 8/1-3 4/3-2
2/1-6x61-8/3 8/5-4 8/1-2
7x61-8/3 4/3-4 4/3-5
4/3-2x31-2/1
2
4/1 2/1-1
0084 0046
3x31-2/1 2/1 2/1-1
4/1-3x31-2/1 4/3 61/31-1
4/3-3x31-2/1 4/1 4/1-2
4x31-2/1 2/1-1 2/1-2
4/1-4x31-2/1 2/1-1 4/1-1
2/1-4x31-2/1 4/3-1 3
2/1-5x31-2/1 3 4/3-2
6x31-2/1 2/1-3 2/1-2
7x31-2/1 2/1-4 8/3-2
2/1-8x31-2/1 6 2/1-2
01x31-2/1 2/1-7 2/1-2
21x31-2/1 2/1-9 2/1-2
2/1-3x11-8/5
2/1-2
8/3 8/7-1
0056 0049
4x11-8/5 8/7 2/1-2
2/1-4x11-8/5 8/3-1 8/7-2
5x11-8/5 8/7-1 8/3-3
2/1-5x11-8/5 8/3-2 2/1-2
6x11-8/5 8/7-2 8/3-4
7x11-8/5 8/7-3 8/3-5
2/1-8x11-8/5 8/3-5 8/5-1
01x11-8/5 8/7-6 2/1-2
21x11-8/5 8/7-8 4/1-2
-
Anchors
267
MaterialSpecifications Wedge Anchor
DescriptionA four-piece assembly consisting of (1) an anchor bolt threaded at one end with a unified pitch, and a shoulder at the opposite end whichretains a free-spinning clip, (2) a clip with three lateral slits and projections designed to exert greater holding power the greater the load
that is applied, (3) a hex nut, and (4) a flat washer.
Applications/Advantages
These are heavy-duty, non-bottom bearing anchors of greater shear strength than other light and medium-duty expansion anchors. Thedesign of the expansion clip assures full contact with the masonry. Wedge anchors withstand temperature fluctuations well. For best
performance, minimum anchor spacing should be 10 hole diameters and minimum edge distance be 5 hole diameters.
Material
Carbon Steel Type 304 Stainless
Anchor Body: AISI 1018 - 12L14 or equivalent free-machiningcarbon steel
Expansion Wedge: AISI C1008 - 1010 or equivalent carbon steelNut: ASTM A-563 Grade-A carbon steel
Washer: Carbon steel
Anchor Body: Type 304Cu (1/4" thru 3/4" diameters)Type 304 (7/8 thru 1-1/4" diams & all lengths over 7")
Expansion Wedge: Type 304 stainlessNut: 18-8 stainless
Washer: 18-8 stainless
Ultimate ShearStrength
See average test values as listed in above table. Important: The maximum working loads should not exceed 1/4 of the average ultimatevalues for a specific size.
Plating Steel wedge anchors are typically zinc or mechanically galvanizedplatedStainless wedge anchors are usually supplied without any additional
coating.
OBCI A DEVORPP W EGDE A SROHCN ,IIpuorG523-S-FF 1ssalC,4epyTLxW
tnemdebmEmuminiM)sehcni(
oTpUlairetaMsnetsaF htgneLdaerhT
seulaVraehS&elisneTetamitlUegarevA
eziSrohcnAetercnocisp0004 etercnocisp0002
elisneT raehS
4/1-4x01-4/3
3
2/1 2/1-2
0027 008,41
2/1-4x01-4/3 01/7 2/1-2
4/3-4x01-4/3 1 8/1-2
2/1-5x01-4/3 4/3-1 4/3-2
6x01-4/3 5/1-2 2/1-2
4/1-6x01-4/3 2/1-2 3
7x01-4/3 4/1-3 4/1-2
2/1-8x01-4/3 4/3-4 8/3-2
01x01-4/3 4/1-6 8/3-2
21x01-4/3 4/1-8 2/1-2
6x9-8/7
2/1-3
8/5-1 2/1-2
008,21 005,128x9-8/7 8/5-3 2/1-2
01x9-8/7 8/5-5 4/1-2
6x8-1
4
1 2/1-2
007,31 003,729x8-1 4 4/1-2
21x8-1 7 2/1-2
9x7-4/118/5-5
8/1-2 4/1-3023,72 530,83
21x7-4/11 8/1-5 4/1-3