Seite 1
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
CHEMICAL RESISTANCEOF SILICONE RUBBER
CHEMISCHE BESTÄNDIGKEITVON SILIKON
In compliance with DIN 53521 each material specimen was immersed for 7 days at the temperature shownin the table. The data measured after immersion relate to products in swelled state:
Die Lagerung der Materialproben wurde jeweils 7 Tage bei der in ter Tabelle angegebenen Temperaturgemäß DIN 53521 durchgeführt. Die Meßwerte nach Lagerung wurden in gequollenem Zustand ermittelt.
The following types have been tested: Folgende Typen wurden getestetSTQ Standard Silicone Grade
for technical applicationsOLQ chemically stabilized silicone,
so-called oil-resistant siliconeFLQ fluorosilicone
STQ Standard Silikon f. technische AnwendungenOLQ chemisch stabilisiertes Silikon sog.
ölbeständiges SilikonFLQ Fluorsilikon
Explanation of the EVALUATION column: Die in der Spalte „Beurteilung“angegebenen Markierung bezeichnen:
A No limit to the use of Products under theconditions mentioned.
A Produkte können unter den genanntenBedingungen ohne Einschränkungeneingesetzt werden.
B Products can only be used in a limited rangeof applications, partly depending on thetype of stress they are subject to. There arepronounced differences between temporaryand permanent exposure, as well asbetween complete immersion in themedium and partial contact with it.
B Produkte sind nur für manche Zweckeverwendbar. Die Art der Beanspruchung istmitentscheidend. Deutliche Unterschiedebestehen zwischen vorübergehender unddauernder Einwirkung, zwischen völligemEintauchen in das Medium und einerstellenweisen Berührung.
C Products should not be used under the conditionsmentioned.
C Produkte sollten unter genannten Bedingungennicht eingesetzt werden.
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
STQ 3 -28 -2 1 AOLQ 1 -65 -100 11 AAcetamide
Acetamid 150FLQ 16 -84 -100 -1 CSTQ -10 -42 -31 32 AOLQ -9 -14 -10 24 A
AcetoneAceton 20
FLQ -29 n.a. n.a. 250 C
Seite 2
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
STQ -20 -60 -50 60 AOLQ -15 -21 -13 38 A56FLQ n.a. n.a. n.a. n.a. CSTQ -1 -3 -15 2 AOLQ -12 -60 -64 7 B20FLQ n.a. n.a. n.a. n.a. BSTQ -49 n.a. n.a. n.a. COLQ n.a. n.a. n.a. n.a. C
Formic acid, conc.Ameisensäure konz.
100FLQ 11 -41 -55 2 BSTQ 12 -27 -16 2 AOLQ 5 -14 -45 2 BAmmonia, conc.
Ammoniak konz. 20FLQ 3 n.a. n.a. 3 CSTQ -24 -73 -78 239 BOLQ -20 -47 -65 132 BWhite spirit, 90/110
Benzin 90/110 20FLQ -14 -19 -16 20 ASTQ -2 -3 -10 1 A
20OLQ -1 -3 -8 2 ASTQ -5 -4 -6 3 A
Benzyl alcoholBenzylalkohol
100OLQ -4 -5 -9 2 ASTQ -2 -5 15 3 AOLQ -8 -48 -50 8 BBrake fluid
Brems-flüssigkeit 100FLQ -4 -65 -42 2 BSTQ -32 -79 -55 97 BOLQ -35 -73 -10 69 BButanol
Butanol 117FLQ -16 -49 -26 19 ASTQ -25 -73 -73 152 BOLQ -20 -44 -55 85 BButyl acetate
Butylacetat 20FLQ -54 n.a. n.a. 236 CSTQ 1 -11 6 0 AOLQ 1 -5 -10 0 ACalcium hydrox., sat.
Calciumdioxid ges. 20FLQ 1 0 0 0 ASTQ -29 -91 -91 244 BOLQ -19 -64 -70 125 BChloroform 20FLQ -20 -37 -23 41 ASTQ -26 -71 -76 233 BOLQ -20 -43 -60 131 B20FLQ -14 -17 -13 19 ASTQ -27 -86 -87 241 BOLQ -20 -51 -65 138 B
CyclohexaneCyclohexan
81FLQ -15 -27 -24 27 A
Seite 3
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
STQ -1 -14 0 3 AOLQ -1 3 -10 2 A20FLQ -20 -52 -29 31 BSTQ -10 -20 -23 18 AOLQ -8 -12 -17 15 A
Diacetone alcoholDiaceton-alkohol
168FLQ n.a. n.a. n.a. n.a. CSTQ -30 -71 -85 147 BOLQ -18 -61 -53 151 B20FLQ n.a. n.a. n.a. n.a. ASTQ -46 n.a. n.a. 340 COLQ -41 n.a. n.a. 171 C
Dibutyl etherDibutylether
142FLQ -17 -53 -29 25 B
STQ -2 -20 18 2 ADimethyl formamideDimethyl- formamid 100
OLQ -3 -16 0 0 ASTQ -25 -58 -62 77 B1,4-Dioxane
1,4 Dioxan 101OLQ -18 -30 -47 76 ASTQ -1 -16 -3 -1 AOLQ -3 -18 10 5 A20FLQ -9 -14 -5 7 ASTQ -21 -72 -92 8 C
Acetic acid, conc.Essigsäure konz.
100OLQ -18 -68 -85 10 CSTQ -1 -6 7 1 AOLQ -1 3 0 5 AAcetic anhydride
Essigsäure-anhydrid 20FLQ -13 -24 -8 12 ASTQ -22 -72 -69 110 BOLQ -17 -39 -45 66 BEthyl acetate
Essigsäure-ethylester 20FLQ -33 n.a. n.a. 228 CSTQ -5 -29 -15 7 AOLQ -5 -18 0 6 A20FLQ -6 -17 -8 3 ASTQ -14 -45 -15 19 BOLQ -11 -36 5 12 B
Ethanol
78FLQ -12 -24 0 8 A
GREASE - FETTESTQ -3 -8 6 3 AOLQ -1 0 5 2 ACoconut oil
Kokosfett 100FLQ -6 10 -18 -1 ASTQ -18 -59 -6 20 BBall bearing grease
Kugellagerfett150
OLQ -13 -30 10 15 A
Seite 4
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
FLQ 11 -41 -55 0 BSTQ -2 3 9 0 AOLQ -1 -2 0 9 AMargarine
Margarine 100FLQ 4 7 -16 0 ASTQ -9 -11 -2 15 AOLQ -6 -10 10 10 AVaseline
Vaseline 150
FLQ 6 4 -26 1 ASTQ n.a. -81 -71 n.a. COLQ n.a. -89 -50 n.a. CHydrofluoric acid, 5%
Flusssäure 5%ig 20FLQ n.a. -20 -12 n.a. CSTQ -1 2 6 0 AOLQ 0 0 -10 1 AGlycol
Glykol 20FLQ 0 -3 0 0 ASTQ 0 -4 15 0 AOLQ -1 3 -15 4 AGlycol/Water 50:50
Glykol/Wasser 50:50 20FLQ 0 -3 0 -1 ASTQ -1 0 7 0 AOLQ -1 -19 -20 4 AGlycerol
Glyzerin 100FLQ -1 3 -5 0 ASTQ -23 -74 -78 239 BOLQ -18 -41 -65 129 BHexane
Hexan 20FLQ -14 -20 -18 22 ASTQ -46 -74 -100 155 COLQ -60 n.a. n.a. 87 CIsopentanol 132FLQ -29 -84 -29 27 BSTQ -14 -12 -20 24 AOLQ -10 -7 -12 23 A20FLQ n.a. n.a. n.a. n.a. ASTQ -20 -69 -53 67 BOLQ -19 -35 -20 42 B
2-PropanolIsopropanol
82FLQ -14 -28 -16 15 ASTQ 0 -9 0 0 AOLQ -1 -6 5 0 A
Potassiumdichromate, 20%
Kalium-dichromat20%ig
20FLQ 0 0 -5 0 ASTQ -1 -10 9 -1 BOLQ -2 -14 -5 0 B
Caustic potashsolution, 50%
Kalilauge 50%ig20
FLQ -4 -6 8 0 BSTQ -2 -1 6 0 AOLQ -1 3 10 0 A
Solution of commonsalt, 10%
Kochsalz-lösung10%ig
20FLQ 0 -7 0 0 A
Seite 5
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
STQ -4 -5 8 3 AOLQ -10 -86 -50 -3 BMethanol 65FLQ -9 -26 -13 4 ASTQ -24 -71 -62 102 BOLQ -23 -41 -45 80 BMethyl ethyl ketone
Methylethyl-keton 80FLQ n.a. n.a. n.a. n.a. CSTQ -22 -70 -69 154 BOLQ -14 -33 -55 86 BDichloromethane
Methylen-chlorid 20FLQ -25 -66 -58 66 BSTQ -23 -69 -64 117 BOLQ -17 -33 -50 66 BMethyl methacrylate
Methyl-methacrylat 20FLQ -29 -80 -68 114 BSTQ -1 7 9 1 AOLQ -1 -5 5 1 ASodium chlorate, 20%
Natriumchlorat 20%ig 20FLQ 0 -1 0 1 ASTQ -2 -31 -11 0 AOLQ 0 3 -5 0 A
Sodium carbonate,saturated
Natrium-carbonat ges.20
FLQ 0 3 5 0 ASTQ -3 -19 0 1 AOLQ -3 -13 -5 -1 A
Caustic soda solution,10%
Natronlauge 10%ig20
FLQ -1 4 8 0 ASTQ -2 -20 -7 0 AOLQ -15 -75 -50 -14 C80FLQ 3 -3 -13 -1 ASTQ -3 -8 2 2 AOLQ -4 -11 0 6 A
Caustic soda solution,30%
Natronlauge 30%ig20
FLQ -3 -6 5 0 ASTQ -3 -17 2 3 BOLQ -7 -35 0 11 B
Caustic soda solution,50%
Natronlauge 50%ig20
FLQ -5 -6 13 3 BSTQ -1 5 6 1 AOLQ 0 -6 10 0 A
Sodium perchlorate,20%
Natrium-perchlorat20%ig
20FLQ 0 1 0 0 ASTQ 1 -3 -4 -1 AOLQ 0 5 -5 -1 A20FLQ 0 0 -5 -1 ASTQ n.a. n.a. n.a. n.a. COLQ n.a. n.a. n.a. n.a. C
Schwefelsäure 10%igSchwefelsäure 10%ig
80FLQ 5 4 0 0 B
Stearic acid 150 STQ 21 -88 -100 -4 C
Seite 6
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
OLQ 9 n.a. n.a. 0 CStearinsäureFLQ 16 n.a. n.a. 1 CSTQ -21 -65 -62 90 BOLQ -16 -29 -40 56 BStyrene
Styrol 20FLQ -16 -16 -5 19 ASTQ -27 -74 -72 195 BOLQ -23 -44 -55 117 BTurpentine
Terpentin 20FLQ -10 -13 -13 11 ASTQ -28 n.a. n.a. 218 BOLQ -23 -64 -55 136 BTetra-hydrofuran 65FLQ -34 n.a. n.a. 253 CSTQ -24 -73 -73 179 BOLQ -19 -37 -50 99 BToluene
Toluol 20FLQ -18 -24 -23 28 ASTQ 0 0 2 -1 AOLQ 0 5 0 0 A
Detergent solution, 1%Waschmittel-lösung
1%ig20
FLQ 0 -3 -3 -1 ASTQ -1 0 5 0 AOLQ 0 5 -5 0 AWasserstoff-peroxid
10%ig 20FLQ 0 -3 0 0 ASTQ 0 -8 15 0 AOLQ 0 10 0 0 A
Hydrogen peroxide,30%
Wasserstoff-peroxid30%ig
20FLQ 1 -1 5 0 ASTQ -24 -71 -71 170 BOLQ -20 -40 -55 97 BXylene
Xylol 20FLQ -16 -20 -18 23 A
Oils - ÖLE STQ -22 -65 -60 90 BOLQ -17 -24 -35 54 BDiesel fuel
Dieselöl 20FLQ -4 -14 -8 4 ASTQ -2 -11 11 -1 AOLQ -2 -19 -10 4 ALinseed oil
Leinöl 100FLQ 4 -3 -13 -1 ASTQ n.a. n.a. n.a. n.a. COLQ -4 -84 -95 4 B
Gear oil SAE 90Getriebeöl
SAE 90150
FLQ n.a. n.a. n.a. n.a. CSTQ -4 -19 16 4 AOLQ 0 3 0 2 A
Mineral oil ASTM-1Mineralöl
ASTM 1 150FLQ 5 -13 -18 -1 A
Seite 7
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
STQ -7 -7 16 9 BOLQ -2 -3 -5 6 A
Mineral oil ASTM-2Mineralöl
ASTM 2150
FLQ 9 -14 -40 0 BSTQ -42 -98 -96 41 COLQ -15 -21 -10 38 B
Mineral oil ASTM-3Mineralöl
ASTM 3150
FLQ 6 -56 -68 2 BSTQ -23 -89 -49 22 BOLQ -9 -18 0 14 A
Engine oil SAE 20
MotorenölSAE 20
150FLQ 5 -6 -26 1 ASTQ -17 -69 -13 17 BOLQ -6 -14 -5 10 A
Engine oil SAE 30Motorenöl
SAE 30150
FLQ 5 -6 -23 1 ASTQ -2 2 16 0 AOLQ -1 6 15 0 AOlive oil
Olivenöl 150FLQ 6 7 -18 -1 ASTQ -20 -52 -41 31 BOLQ -13 -5 -43 27 B
Silicone Fluid AK 100Silikonöl
AK 100150
FLQ 1 -3 -3 -1 ASTQ -13 -34 -16 25 BOLQ -9 -8 15 14 A
Silicone Fluid AK 350Silikonöl
AK 350150
FLQ 3 0 -2 -1 ASTQ -10 -27 -11 21 BOLQ -6 8 5 11 A
Silicone Fluid AK 500Silikonöl
AK 500150
FLQ 5 1 -3 -2 ASTQ -4 -2 -15 5 AOLQ -3 9 -11 4 A
Silicone Fluid AK 1250Silikonöl
AK 12500150
FLQ 5 3 -11 -1 ASTQ -13 -15 -18 17 BOLQ -10 -8 -7 14 A
Silicone Fluid AP 100Silikonöl
AP 100150
FLQ 1 1 2 0 ASTQ -10 -12 -10 12 AOLQ -7 -3 -4 12 A
Silicone Fluid AP 500Silikonöl
AP 500150
FLQ 3 3 0 0 ASTQ -31 -62 -56 90 BOLQ -20 -10 -41 75 B
Silicone Fluid AR 20Silikonöl
AR 20150
FLQ 2 -4 5 3 ASTQ -22 -46 -42 36 BOLQ -16 -2 -20 32 B
Silicone Fluid AP 200Silikonöl
AP 200150
FLQ 3 3 -3 0 A
Petroleum ether 20 STQ -25 -73 -76 244 B
Seite 8
Obige Daten wiedergeben Ergebnisse von Laborprüfungen, die an vonnormalisierten Prüfkörpern mit aller Sorgfalt durchgeführt wurden und sollenkönnen lediglich als Hilfe bei der Materialauswahl genutzt werden. DerEndabnehmer ist von eigenen Freigabeprüfungen vor dem Materialeinsatznicht entbunden. Alle Angaben ohne gewähr.The above data reflect the results of laboratory tests that were conducted onnormalized specimens with the utmost care and will may only be used as anaid in material selection. The end user is not released of their own trialsbefore the use of materials. All data without guarantee.
silicone & rubber technologies
Test medium Testtemperat. °C Grade
Changein Shore
AChange in tear
strenghtChange in
elongation atbreak
Change involume Evaluation
PRÜFMEDIUMPrüf-
temperatur°C
TypeÄnderungShore A
Pkt.
ÄnderungReißfestigkeit
%
ÄnderungReißdehnung
%
ÄnderungVolumen
%Beurteilung
OLQ -18 -25 -50 132 BPetrolätherFLQ -15 -25 -18 22 ASTQ 0 -1 6 -1 AOLQ 1 0 -5 0 A20FLQ -1 -3 -3 0 ASTQ 0 -30 -32 0 AOLQ 3 -23 -25 -1 A
Phosphoric acid, 30%Phosphorsäure 30%ig
100FLQ n.a. n.a n.a. n.a. ASTQ 0 -4 4 0 AOLQ 0 2 0 0 A20FLQ 0 -1 3 0 ASTQ 1 -42 -21 0 BOLQ 2 -50 -23 -1 B
Phosphoric acid, 50%Phosphorsäure 50%ig
100FLQ n.a. n.a n.a. n.a. BSTQ 0 -21 -10 -1 BOLQ 0 -2 -10 -1 APhosphoric acid, 85%
Phosphorsäure 85%ig 20FLQ 0 1 8 -1 ASTQ -1 -43 9 2 AOLQ 3 -29 5 2 APhthalic anhydride
Pthalsäure-anhydrid 150FLQ 12 -43 5 9 BSTQ -1 -51 -15 1 BOLQ -15 -94 -100 20 CSalpetersäure 5%ig
Salpetersäure 5%ig 80FLQ 1 -11 -3 1 ASTQ -2 -24 -15 0 BOLQ -4 -73 -80 6 CSalpetersäure 10%ig
Salpetersäure 10%ig 20FLQ 0 1 5 0 ASTQ 6 -93 -100 3 COLQ -9 n.a n.a. 19 CSalpetersäure 65%ig
Salpetersäure 65%ig 20FLQ 3 -24 -29 1 CSTQ 0 -4 -5 0 AOLQ -2 -68 -80 2 C20FLQ -1 0 -5 0 ASTQ -1 n.a n.a. 3 COLQ -16 n.a n.a. 30 C
Hydrochloric acid,10%
Salzsäure 10%ig80
FLQ 0 -13 3 0 BSTQ 5 n.a n.a. n.a. COLQ n.a. n.a n.a. n.a. C
Hydrochloric acid,30%
Salzsäure 30%ig20
FLQ 1 -6 -11 1 B