hanit® Installation Guide- 5 Bar Pasture Fence System -
HAHN Kunststoffe GmbH - Gebäude 1027 - DE 55483 Hahn-Flughafen
Telefon: +49 (0)65 43 / 98 86-0 Mail: [email protected]
Fax: +49 (0)65 43 / 98 86-99 Online: www.hahnkunststoffe.com
YEAR WA R RANTY
HAH
N KUNSTSTOFFEThank you for choosing the hanit® Pasture Fence System.
The following contains important information that should be considered during the setup.
General Information:
• All profiles can be worked with conventional tools. More information about processing and tool selection can be found
at www.hahnplastics.com.
• All details of this manual, especially the information about clearance and distances, are based on an installation tempe-
rature of 20°C.
• The manual can be amended to technical changes and new knowledge anytime and without notice.
• The components consist of recycled plastics. Differences in colour and surface structure are possible and no reason for
reclamation. Deviations dimensions (+/- 3%) are also possible due to the material.
System Description
The pasture fence system is designed as a modular construction. The crossbars will be fixed on the paddock posts.To finalise the installation, use the end post of the fence for corner constructions, plus the standard connector when moun-ting edges.
Components – 5 Bar
Pasture post - WxHxL: 10x11x230 cmKoppelendpfosten - BxHxL: 10x11x230 cm Board with Reinforcement - WxHxL: 4,2x12x250 cm
Standard connector 90° Countersunk Bolt Ø6x70 mmCarriage Bolt M10x110 mm
HAHN Kunststoffe GmbH - Gebäude 1027 - DE 55483 Hahn-Flughafen
Telefon: +49 (0)65 43 / 98 86-0 Mail: [email protected]
Fax: +49 (0)65 43 / 98 86-99 Online: www.hahnkunststoffe.com
YEAR WA R RANTY
HAH
N KUNSTSTOFFE
hanit® Installation Guide- 5 Bar Pasture Fence System -
Step 1
The pasture posts should be installed at 250cm clear width.
The embedded depth of the post in a frost-proof concrete foundation(WxL: 50x50) amounts to 70 cm. Concrete class: C16/20. Make sure thatthe post stands out about 160 cm out of the ground.
The allowed soil pressure at the area of the foundations should amount to 150 kN/m². This should be checked before concreting.
Step 2
Insert the crossbars into the designated pasture post recesses.
Adjust the crossbars so that they can appear the same in each recess in each post.
Step 4
Screw the standard connector with a 90° angle through the pre-drilled holesonto the paddock post with two screws (Ø6x70mm).
Since the crossbars Endpost are placed onto the corner, the first panel will be wider. Be aware while placing the paddock posts.
Alternatively, the boards of the first panel can be shortened to get a consistent panel width. We recommend shortening on both profile sides. By shortening, the covering caps are gone.Please secure the crossbar according to step 3 with carriage bolts.
Please note:The standard connector allows slight variations from the 90° angle thanks tointegrated leeway.
Zoning and sub-dividing paddocks, meadows and runs are also possible.
250 cm
160
cm
Step 3
Pre-drill the crossbars and posts with a Ø13mm drill. Screw each crossbar together with 2 carriage boltsM 10x110 mm, as well as with suitable acorn nuts and washers.
In order to avoid injuries, we recommend to mount the acorn nuts on theouter side, so that the carriage bolt heads are located on the inside.
HAHN Kunststoffe GmbH - Gebäude 1027 - DE 55483 Hahn-Flughafen
Telefon: +49 (0)65 43 / 98 86-0 Mail: [email protected]
Fax: +49 (0)65 43 / 98 86-99 Online: www.hahnkunststoffe.com
YEAR WA R RANTY
HAH
N KUNSTSTOFFEAssembly on incline
With an incline of more than 10%, the recesses on the downhill side may have to be released.
hanit® Installation Guide- 5 Bar Pasture Fence System -